Annonces KM235/1 Stereo Microphone Bar
Alerte nouvelle annonceAvis
4.0/5(2 avis)
100 %
Donner un avis
JeffTadashiSi vous avez besoin de deux micros sur un support ...
Publié le 21/06/12 à 04:58
(contenu en anglais)The AKG KM235/1 Stereo Microphone Bar is a small, versatile microphone stand accessory that can hold two microphone clips onto a single stand. It is 8.5" in total length, and it has three separate sections: The primary bar that screws onto a single american mic stand threading, and two pivotable arms. The two arms are very tight, and only move when you are adjusting them; there is no need to loosen and retighten the arm positions at all. They can pivot the full 360 degrees, given that the other arm doesn't get in the way.
To attach the two mic clips, there is a special metal part that both screws into the arm, and screws into a mic clip. This way, you can adjust the depth of the special metal part, in case you have a mic clip that has either a shallow or deep threading inside of it. However, this setup has a lot of extra moving parts, threadings, and it can be a bit confusing to get the mic clips threaded correctly, and tightened in the correct position. You may have to buy or use a mic thread washer in order for the mic clip to be tightened in the correct position, and I know I have some problems setting it up properly. However, the special metal part is easily adjusted by hand, as the handle is very wide.
OVERALL OPINION
The overall material of this microphone bar is very solid, all metal and no cheap plastic anywhere. It is aesthetically simple and clean, and for the most part, it functions just as intended. If you need to hold two mics in an a/b position for drum overheads, or use them for other stereo setups, this accessory can reduce the number of stands and clutter of your stereo setup. Be sure to try it out first, and see if it works with your mic clips.
To attach the two mic clips, there is a special metal part that both screws into the arm, and screws into a mic clip. This way, you can adjust the depth of the special metal part, in case you have a mic clip that has either a shallow or deep threading inside of it. However, this setup has a lot of extra moving parts, threadings, and it can be a bit confusing to get the mic clips threaded correctly, and tightened in the correct position. You may have to buy or use a mic thread washer in order for the mic clip to be tightened in the correct position, and I know I have some problems setting it up properly. However, the special metal part is easily adjusted by hand, as the handle is very wide.
OVERALL OPINION
The overall material of this microphone bar is very solid, all metal and no cheap plastic anywhere. It is aesthetically simple and clean, and for the most part, it functions just as intended. If you need to hold two mics in an a/b position for drum overheads, or use them for other stereo setups, this accessory can reduce the number of stands and clutter of your stereo setup. Be sure to try it out first, and see if it works with your mic clips.
00
»
JeffTadashiSi vous avez besoin de deux micros sur un stand ...
Publié le 21/06/12 à 04:59 (contenu en anglais)The AKG KM235/1 Stereo Microphone Bar is a small, versatile microphone stand accessory that can hold two microphone clips onto a single stand. It is 8.5" in total length, and it has three separate sections: The primary bar that screws onto a single american mic stand threading, and two pivotable arms. The two arms are very tight, and only move when you are adjusting them; there is no need to loosen and retighten the arm positions at all. They can pivot the full 360 degrees, given that the other arm doesn't get in the way.
To attach the two mic clips, there is a special metal part that both screws into the arm, and screws into a mic clip. This way, you can adjust the depth of the special metal part, in case you have a mic clip that has either a shallow or deep threading inside of it. However, this setup has a lot of extra moving parts, threadings, and it can be a bit confusing to get the mic clips threaded correctly, and tightened in the correct position. You may have to buy or use a mic thread washer in order for the mic clip to be tightened in the correct position, and I know I have some problems setting it up properly. However, the special metal part is easily adjusted by hand, as the handle is very wide.
OVERALL OPINION
The overall material of this microphone bar is very solid, all metal and no cheap plastic anywhere. It is aesthetically simple and clean, and for the most part, it functions just as intended. If you need to hold two mics in an a/b position for drum overheads, or use them for other stereo setups, this accessory can reduce the number of stands and clutter of your stereo setup. Be sure to try it out first, and see if it works with your mic clips.
To attach the two mic clips, there is a special metal part that both screws into the arm, and screws into a mic clip. This way, you can adjust the depth of the special metal part, in case you have a mic clip that has either a shallow or deep threading inside of it. However, this setup has a lot of extra moving parts, threadings, and it can be a bit confusing to get the mic clips threaded correctly, and tightened in the correct position. You may have to buy or use a mic thread washer in order for the mic clip to be tightened in the correct position, and I know I have some problems setting it up properly. However, the special metal part is easily adjusted by hand, as the handle is very wide.
OVERALL OPINION
The overall material of this microphone bar is very solid, all metal and no cheap plastic anywhere. It is aesthetically simple and clean, and for the most part, it functions just as intended. If you need to hold two mics in an a/b position for drum overheads, or use them for other stereo setups, this accessory can reduce the number of stands and clutter of your stereo setup. Be sure to try it out first, and see if it works with your mic clips.
00
»
Fiche technique
- Fabricant : AKG
- Modèle : KM235/1 Stereo Microphone Bar
- Catégorie : Pieds/perches/socles pour microphones
- Fiche créée le : 11/06/2012
Nous n'avons pas de fiche technique sur ce produit
mais votre aide est la bienvenue
Distribué par Freevox
»
Autres catégories dans Accessoires microphones
Autres dénominations : km235/1 stereo microphone bar, km235/1 stereomicrophonebar, km235/1stereomicrophonebar, km235 1 stereo microphone bar, km 235/1 stereo microphone bar, km235/1stereo microphone bar, km2351 stereo microphone bar, km235/1 stereo microph 1 bar, km2351 stereomicrophonebar, km235/1 stereomicroph 1 bar, km2351stereomicrophonebar, km235/1stereomicroph 1 bar, km235 1 stereo microph 1 bar, km 2351 stereo microphone bar, km 235/1 stereo microph 1 bar, km2351stereo microphone bar, km235/1stereo microph 1 bar