SPL Performer s800

• Bi polar transistor power amplifier with VOLTAiR 120V technology
• 2 x 285 W into 4 ohms; 2 x 185 W into 8 ohms (stereo operation) 
• 450 W into 4 or 8 ohms (mono operation – Bridge Mode)
• Toroidal transformer with 855 VA
• 40800 µF capacitance for faithful reproduction of impulse peaks
• Gold-plated loudspeaker binding posts with protection covers
• Neutrik XLR connectors for balanced in- and outputs
• Direct slave through of the input (e.g. for bi-wiring)
• Input trim switch for attenuation up to -5.5 dB in 0.5 dB steps
• AMP CTR connector for remote power on/off switching (e.g. with Director or Phonitor x)
• Overheat protection with Temp LED
• DC (direct current) voltage protection with Protect LED
• Made in Germany

Line Inputs & Line Outputs

• Neutrik XLR, balanced, Pin 2 = (+)
• Input impedance: 10 kohms
• Input trimming: 0 dB to -5.5 dB in 0.5 dB steps 
• Input sensitivity: Single-ended or balanced: 3.03 V RMS
• Output impedance: defined by connected device
• Crosstalk: -110 dB (@1 kHz) 

Loudspeaker Outputs

• 2 pairs binding posts with ø4mm cable hole (screwable) and banana plug; fully encapsulated

 Output power

• 2x 285 W RMS into 4 ohms
• 2x 185 W RMS into 8 ohms
• 1x 450 W RMS into 4 or 8 ohms in bridge mode 

Output voltage

• 74 V Peak-to-Peak (stereo)
• 180 V Peak-to-Peak (bridge)

• 35 V RMS (stereo)
• 86 V RMS (bridge)

Output impedance

• < 0.031, 20 Hz to 20 kHz (stereo)
• < 0.043, 20 Hz to 20 kHz (bridge)

Damping factor

• > 300, 20 Hz to 20 kHz, at 8 ohms (stereo)
• > 190, 20 Hz to 20 kHz, at 8 ohms (bridge)

Frequency response

• 9 Hz to 100 kHz +0, –0.03 dB
• < 9 Hz to 200 kHz +0, –3 dB

Signal-to-noise ratio

• > 118 dB (wide-band, unweighted, referred to full power output)
• > 123 dB (A-weighted)

Gain

• 26 dB (stereo)
• 32 dB (bridge)

Total harmonic distortion

• < 0.03 % at 1 kHz, at 185 W, 8 ohms 
• < 0.19 % at 20 kHz, at 185 W, 8 ohms
• < 0.011 % at 1 kHz, at 450 W, 8 ohms
• < 0.12 % at 20 kHz at 450 W, 8 ohms

Power Supply

• Mains voltage (switchable): 230 V AC / 50 Hz or 115 V AC / 60 Hz
• Fuses: 230 V: T 4 A; 115 V: T 8 A 
• Power consumption: max 900 VA
• Idle power consumption: 40 W

Dimensions (incl. feet)

• 278 mm W x 100 mm H x 370 mm D
• 10.95" W x 3.94" H x 14.57" D 

Weight

• 12.8 kg; 28.2 lbs (unit only) 
• 14.0 kg; 30.9 lbs (shipping)