Collecte d' informations sur la série H3000 de chez Eventide

Un technicien mais ou? J'ai pensé à Music Power, s'ils ne le font pas ils connaissent sans doute quelqu'un qui saurait faire ça. Mais j'ai surtout peur de la facture.

Bon pour ceux qui seront confrontés aux même problèmes et qui maitrisent bien l'anglais je laisse le texte qui était fourni dans l'annonce sur ebay. J'ai du trouver moi même le schéma qui correspond aux indications fournies dans le texte. Pas malin les petits revendeurs.

This document describes the procedure for adding the features of the H3000-D/SE to any H3000, H3000-S, H3000-D/SX, or H3000-B Ultra-Harmonizer. If your unit has an operating system version of 2.16 or lower you must perform all of the modifications listed herein. If you have an H3000-B, H3000-S, or H3000-D/SX with an operating system of 2.17 or higher, skip the CUT AND JUMP section.

In some cases, you will have to do without the presets and some features you are used to until an EPROM exchange is made. As a consolation, you will have use of all the algorithms and presets of the H3000-D/SE to play with while the other EPROMs are in the exchange process. Be sure to read WHAT TO DO WITH THE LEFT OVER EPROMS section before doing the installation to determine if an exchange is required. 


BEFORE BEGINNING

Save your presets! This modification procedure will cause all of your presets to be erased. If you have a computer with "MIDI Librarian" software, transfer them to the computer as described in the manual. If you don't, write down the settings for each parameter. NOTE: This only applies to units with an operating system of 2.16 or higher. Many of the parameters in operating system versions 2.11 and lower have been changed in successive revisions and are not compatible with the new operating system.

The MODIFICATION KIT (D/SECONKIT) comprises the following components:

3 EPROMS:
1 x D/SX&D/SE ROM1 V2.17 Operating System
1 x D/SX&D/SE ROM2 V2.17 Main Algorithms
1 x D/SE ROM3 V 2.17/2M Algorithms & Presets

You will also need:

Soldering iron and electronic-grade solder
Small phillips screwdriver
A cutting tool such as an Exacto knife or razor blade

1. REMOVE POWER FROM THE H3000 by disconnecting the AC power cord. Disconnect all other cables to make access convenient.

2. REMOVE the TOP COVER from the unit by removing the phillips screws around the periphery of the cover.

3 PLACE the UNIT in front of you with the FRONT PANEL facing you. All instructions for the placing of EPROMs in sockets, the cuts, and jumps are described and/or shown with the unit in this position.


CUT AND JUMP PROCEDURE

1. Locate the jumpers marked X1 through X8 found between the software EPROMS installed in the right, rear of the main PC board (see diagram).

2. Using the knife or razor blade, carefully cut between the pads as necessary to make your main pc board match with the cuts indictated in the diagram. Be sure to break the connection completely by insuring that any markings on the PC board that appear between the pads are cut completely through. This will insure a broken connection.

3. Short the pads as necessary to match your main PC board with the connections shown in the diagram. To do this you must create a small pool of solder across pads as indicated in the diagram. Be VERY CARFUL to avoid bridging the gap(s) you created step 2 and avoid soldering anything else!

The pads should now be in exactly the same configuration as indicated in the diagram. Check your work to insure that all connections are broken where cut and there is continuity between the newly jumpered pads. (Note: most of the problems reported to us after an upgrade kit installation are solved simply by double checking the cut and jump work.)

H3000EPROMUpgradeDiagram.jpg picture by mr_pics

INSTALL THE NEW D/SECONKIT EPROMS

1. Remove the Operating System EPROM currently installed in socket U53.

2. Replace this EPROM with the D/SX&D/SE ROM1 V2.17 included with the kit. NOTE: Be sure to install the EPROM with the notch to the left. As this EPROM has fewer pins than the socket, be sure that it is installed flush right.

3. Remove all other software EPROMs. Be sure they are static protected as you may need to re-install them after reading the next section.

4. Install both D/SX&D/SE ROM2 V2.17 and D/SE ROM3 V2.17 in any empty socket. NOTE: be sure to install with the notch to the left.

RESET PROCEDURE

1. Carefully inspect your work for shorts and soldering quality. Be sure that all pins of the EPROMs are inserted fully and none are bent underneath the body of the component.

2. Reconnect the AC power cord to the rear of the unit. The Operating System must now be reset as follows:

FINAL ASSEMBLY

1. Put the top cover back on. The machine screws go in the two holes in the front center of the unit. The remainder of the holes take the self-tapping screws.

 

 

http://img832.imageshack.us/img832/2580/jumperskitdiag1.jpg

Maintenant que tu me dis ça je comprends mieux. J'imaginais qu'il y'avait des composants ou des fils à couper. Moi et mon anglais...

Si j'ai bien compris la connexion et la séparation entre les jumpers doit être faite suivant celle indiquée sur le schéma. Donc 4 jonctions de soudure et 4 séparation avec le cutter?

Je viens de comprendre. En tapant "H3000 diagram" je suis tombé sur des pages ou des types ont effectué l'opération. En effet pas grand chose à faire finalement. En fait il faut effectuer une jonction sur le jumper X6 et rayer celle déjà existante du X5.

http://img254.imageshack.us/img254/3811/img12111e.jpg

En tout cas merci nii tu m'as bien fais avancer

Très très sympa nii! Je n'en demandais pas tant et je pensais pas qu'un membre ferait ça à travers un forum. Quand j'aurai effectué l'opération j'ouvrirai un tutoriel, à mon avis ça pourrait servir. Merci beaucoup!

Hors sujet :

 Joli matos que je vois sur ta fiche. Le line 6 echo sonne très bien d'après ce que j'ai lu. Il y'a un preset space echo dans le H3000, j'ai hâte de tester ça.

Résumé

Liste des algorithmes H3000:

• 100 - Diatonic Shift,
• 101 - Layered Shift,
• 102 - Dual Shift,
• 103 - Stereo Shift,
• 104 - Reverse Shift,
• 105 - Swept Combs,
• 106 - Swept Reverb,
• 107 - Reverb Factory,
• 108 - Ultra-Tap,
• 109 - Long Digiplex®,
• 110 - Dual Digiplex,
• 111 - Patch Factory,
• 112 - Stutter,
• 113 - Timesqueeze®
• 114 - Dense Room,
• 115 - Vocoder,
• 116 - Multi-Shift,
• 117 - Band Delay,
• 118 - String Modeler,
• 119 - Phaser,
• 122 & 123 - mod factory.

Pour plus de précisions sur les algorithmes de chaque version H3000 (9 au total) reportez vous au tableau ici et à la liste complète des presets. D'après le tableau, les algorithmes 120 et 121 ne concernent que la série H3500 qui inclut un sampler.

Désolé pour le retard.

Non, on ne peut pas additionner plusieurs algorithmes. Sur la liste des presets on peut lire sur chacun quel algorithme est utilisé. Mais en réalité les réglages sont si poussés sur chaque algo que cela permet d'obtenir des effets surprenants parfois magnifiques. Ça relève de l'orfèvrerie. Pour ma part je n'ai pas la patience.

Sinon il reste toujours la possibilité d'utiliser un deuxième H3000 ou bien une des nouvelles pédales de la marque.