Bookmarkez un article, une news ou un tuto et retrouvez-le dans votre section "Mes signets" du menu membre.
6 nouveaux annuaires
Luthiers, Réparateurs, Cours de musique, Studios d’enregistrement, de mastering et de répétition... Suggérez l’ajout d’une entreprise, inscrivez la vôtre ou déposez un avis.
Alertes disponibilité et baisse de prix
Ces nouvelles fonctionnalités vous permettent d'être informé·e dès qu'un produit est disponible ou que son prix a baissé.
Tentatives d'arnaque dans les petites annonces
Nous faisons face depuis quelques mois à une recrudescence de tentatives d'arnaques dans les petites annonces. Suivez nos recommandations >
Payez en 3 ou 4 fois vos achats d'occasion
Achetez plus facilement les produits dont vous rêvez grâce au paiement en 3 ou 4x dans les petites annonces.
Notez AF !
Dites-nous ce que vous pensez d'AF sur notre page Trustpilot ! Nous lisons et répondons à tous les avis.
Sujet de la discussionPosté le 06/09/2008 à 12:17:32Comment fais-t-on le reset usine sur le vf 16 ?
Anonyme
1092
2Posté le 13/09/2008 à 20:16:45
Il n'y en a pas.
0
ExSha ka
18
Nouvel·le AFfilié·e
Membre depuis 10 ans
3Posté le 07/02/2017 à 21:41:48
Bonjour à tous,
Si vous savez lire l'anglais, il y a ceci: (Je ne l'ai pas essayé, je ne peux pas tout traduire)
Flash ROM
This mode is used when copying the system software from EPROMs to Flash ROM. As mentioned in the section “3. SOFTWARE UPDATE” (page 8), the VF-16 software inside the Flash ROM can be updated through the SCSI port. However, if something wrong happens when updating the software (e.g. A blackout occurred while updating the software.), the VF-16 might not be able to boot up using the system software inside the Flash ROM.
In this case, the following procedures must be taken.
1. Power off the VF-16 and disconnect the AC cable from the AC IN socket.
2. Plug the VF-16 EPROMs into the ROM CARD PCB assy sockets (U1 and U2). The SW on the ROM CARD PCB assy must be set to “EPROM” side.
3. Open up the top panel assy by loosening screws on both sides and on top, so that the ROM CARD PCB assy can be vertically plugged into the 50-pin connector J5 on the MAIN PCB assy. 4. Connect the AC cable and power on the VF-16.
In this condition, the VF-16 is booted up using the system software inside the EPROMs. The next procedures to take
are as follows.
5. Put the VF-16 into the Service Mode, rotate the jog dial and select “FlashROM” menu.
Then, press the [ENTER/YES] key.
The display indicates the following and “SURE?” will start blinking.
6. Press the [ENTER/YES] key to copy the system software from EPROMs to Flash ROM. The display shows “Erase ROM”, “Write ROM” and then “COMPLETED!” in order.
7. In order to confirm that the VF-16 is correctly booted up using the system software inside the Flash ROM, power off the VF-16, disconnect the ROM CARD PCB assy and power it back on again.
8. After confirming that the VF-16 is booted up using the Flash ROM, referring to the section “3. SOFTWARE UPDATE” (page 8), update the system software inside the Flash ROM through SCSI port to the latest one.
Sinon il y a ceci: (Que je n'ai pas essayé non plus)
Il y a cette avertissement
Product Initialize
This mode is exclusively used at our assembly line and has nothing to do with servicing the unit.
On obtient ce mode en faisant ceci :
While holding down the [stop] key and [shift] key, press the [setup] key.
ce mode se retrouve tout en bas de la liste. (Tourner la grosse molette pour l'atteindre)