Big probleme
- 1 réponse
- 2 participants
- 902 vues
- 1 follower
banji4101
5
Nouvel·le AFfilié·e
Membre depuis 16 ans
Anonyme
76
Bonjour Banji4101
j'ai ta réponse je le pense. j'ai flashé aussi mon rp250 et à la fin de la procédure il est expliqué que tu dois reseter ta machine
Once the update is complete, you will then want to perform a Factory Reset.
Note: a Factory Reset will erase all User presets. This procedure is as follows:
1. Press and hold the Store button while powering up the RP250.
tu maintien le bouton store en allumant l'appareil
2. When the display prompts you with FACRST, release the Store button, which is now flashing.
apparait à l'écran facrst
3. Press and hold the flashing Store button for 3 seconds until RSTORD appears in the display and release. The Factory Reset procedure takes approximately 15 seconds. The Expression Pedal calibration will then commence.
maintien la touche pendant 3 seconde
4. When the Display prompts you with TOE DN, rock the Expression Pedal forward (toe down) and press either Footswitch.
5. When the Display prompts you with TOE UP, rock the Expression Pedal back (toe up) and press either Footswitch.
6. The Display now prompts you to calibrate the V-Switch sensitivity (VSwxxx), where XXX is the current V-Switch threshold. Rock the Expression Pedal forward and press firmly on the toe once to turn the V-Switch on (wah ON), and again to turn the V-Switch off (WAHOFF).
7. If the V-Switch is too sensitive, press the right Up Footswitch to raise the threshold (range is 0-200). Keep testing the V-Switch sensitivity and adjust the threshold until it only engages when you want it to (too sensitive a setting will lead to the V-Switch falsely triggering on or off when using the Expression Pedal).
8. When the V-Switch sensitivity is set to your satisfaction, press both Up/Down Footswitches simultaneously to exit.
Pour le reste j'ai appuyer à chaque fois sur les deux pads de selection en même temps et ça roule maintenant.
J'espère t'avoir répondu
j'ai ta réponse je le pense. j'ai flashé aussi mon rp250 et à la fin de la procédure il est expliqué que tu dois reseter ta machine
Once the update is complete, you will then want to perform a Factory Reset.
Note: a Factory Reset will erase all User presets. This procedure is as follows:
1. Press and hold the Store button while powering up the RP250.
tu maintien le bouton store en allumant l'appareil
2. When the display prompts you with FACRST, release the Store button, which is now flashing.
apparait à l'écran facrst
3. Press and hold the flashing Store button for 3 seconds until RSTORD appears in the display and release. The Factory Reset procedure takes approximately 15 seconds. The Expression Pedal calibration will then commence.
maintien la touche pendant 3 seconde
4. When the Display prompts you with TOE DN, rock the Expression Pedal forward (toe down) and press either Footswitch.
5. When the Display prompts you with TOE UP, rock the Expression Pedal back (toe up) and press either Footswitch.
6. The Display now prompts you to calibrate the V-Switch sensitivity (VSwxxx), where XXX is the current V-Switch threshold. Rock the Expression Pedal forward and press firmly on the toe once to turn the V-Switch on (wah ON), and again to turn the V-Switch off (WAHOFF).
7. If the V-Switch is too sensitive, press the right Up Footswitch to raise the threshold (range is 0-200). Keep testing the V-Switch sensitivity and adjust the threshold until it only engages when you want it to (too sensitive a setting will lead to the V-Switch falsely triggering on or off when using the Expression Pedal).
8. When the V-Switch sensitivity is set to your satisfaction, press both Up/Down Footswitches simultaneously to exit.
Pour le reste j'ai appuyer à chaque fois sur les deux pads de selection en même temps et ça roule maintenant.
J'espère t'avoir répondu
- < Liste des sujets
- Charte