Sujet Tap tempo et loop
- 10 réponses
- 4 participants
- 1 610 vues
- 1 follower
Raf in NJ
312
Posteur·euse AFfamé·e
Membre depuis 21 ans
- 1
- 2
toniodod
181
Posteur·euse AFfiné·e
Membre depuis 22 ans
sergiogibson
2234
AFicionado·a
Membre depuis 21 ans
Raf in NJ
312
Posteur·euse AFfamé·e
Membre depuis 21 ans
toniodod
181
Posteur·euse AFfiné·e
Membre depuis 22 ans
Il ne faut pas envoyer de prog chang pour un preset "tap tempo". SInon la valeur du délai sera remise à la valeur par défaut à chaque appui 
Raf in NJ
312
Posteur·euse AFfamé·e
Membre depuis 21 ans
Ben si parce que ca marche 
et puis y'a le control change avec qui modifie en meme temps le tempo, si tu n'es pas convaincu vas voir la notice du pedalier c marqué noir sur blanc, il faut appeler psieurs fois le patch en cadence et pour avoir le patch il faut un prog change. CQFD
Rafouille
toujours pret a s'en metre plein les fouilles
meme si ca cafouille
il a jamais trouille
et puis y'a le control change avec qui modifie en meme temps le tempo, si tu n'es pas convaincu vas voir la notice du pedalier c marqué noir sur blanc, il faut appeler psieurs fois le patch en cadence et pour avoir le patch il faut un prog change. CQFD
Rafouille
toujours pret a s'en metre plein les fouilles
meme si ca cafouille
il a jamais trouille
Un seul conseil: Lisez les manuels !!!
toniodod
181
Posteur·euse AFfiné·e
Membre depuis 22 ans
Nan nan j'suis certain
toniodod
181
Posteur·euse AFfiné·e
Membre depuis 22 ans
DOnc ça n'est pas un prog change que tu dois envoyé en cadence mais un control change supérieur à 63:
Programming Footswitch (Preset) 5 as a Tap-Tempo Switch:
The Control Change number on the V-Amp to control Tap-Tempo is “64”. Although the actual value sent has no meaning, it requires a Value of “64” or higher to work. So here are the steps to set it up.
1) Select Preset 5 by pressing on footswitch 5.
2) Hold the “Bank Down” switch for 3 seconds.
3) Press the ENTER/UP switch once. The green select LED should be lit. Now that you’re in programming mode, each of the footswitches (1-10) will serve a different purpose depending on what function you’re setting.
4) Make sure all program changes (“PRGCHG1” through “PRGCHG5”) are disabled. The red LEDs should be off for footswitches 1 through 5. If an LED for any one of these switches is ON, that means that Program Change Number is enabled. Press the switch and hold it until the LED goes out.
5) Press switch 6 (CTLCHG 1) briefly so that the red LED flashes. Press ENTER/UP, and enter “64” as the Controller Number, then press ENTER/UP to confirm. Next enter a Value of “64”, then press ENTER/UP to confirm.
6) Make sure the LED for switch 7 (CTLCHG 2) is OFF. If it is ON, Press the switch 7 and hold it until the LED goes out
7) Press switch 8 (EXP A) briefly so that the red LED flashes. Press ENTER/UP, and enter “27” as the Controller Number, then press ENTER/UP to confirm. Next enter a Value of “00” (this is the Low Value), then press ENTER/UP to confirm. Next enter the High Value of “127”, then press ENTER/UP to confirm.
8) Press switch 9 (EXP B) briefly so that the red LED flashes. Press ENTER/UP, and enter “16” as the Controller Number, then press ENTER/UP to confirm. Next enter a Value of “00” (this is the Low Value), then press ENTER/UP to confirm. Next enter the High Value of “127”, then press ENTER/UP to confirm.
9) Press the DOWN switch for 3 seconds.
Now footswitch/preset 5 will function as a Tap-Tempo switch.
Programming Footswitches (Presets) 6 through 10 to select V-Amp Presets 1A through 1E.
Setting up these last 5 presets requires using Program Changes to select the desired patch on the V-Amp. Remember what I stated in the Considerations Section. The V-Amp doesn’t have a Control Change Number to allow you to trigger preset button “A”, you have to use a Program Change to select an actual preset “1A” (Bank 1, Preset A). Program Change 1 = “1A”, 2 = “1B”… all the way up to 125. For example Program Change 14 = “3D”, Program Change 85 = “17E”, etc. Pressing the Bank Up or Down switch will NOT change banks on the V-Amp, it will only change banks on the FCB. If you change banks, all 10 footswitches/presets on the FCB need to be programmed for that bank.
1) Select Preset 6 by pressing on footswitch 6.
2) Hold the “Bank Down” switch for 3 seconds.
3) Press the ENTER/UP switch once. The green select LED should be lit. Now that you’re in programming mode, each of the footswitches (1-10) will serve a different purpose depending on what function you’re setting.
4) Make sure all program changes (“PRGCHG2” through “PRGCHG5”) are disabled. The red LEDs should be off for footswitches 2 through 5. If an LED for any one of these switches is ON, that means that Program Change Number is enabled. Press the switch and hold it until the LED goes out.
5) The LED for PRGCHG1 (switch 1) SHOULD be lit. If it isn’t, press the switch and hold it until the LED turns ON.
6) Press switch 1 (PRGCHG1) briefly so that the red LED flashes. Press ENTER/UP, and enter “01” as the Program Change Number, then press ENTER/UP to confirm.
7) Make sure the LED for switches 6 & 7 (CTLCHG1 and CTLCHG 2) are OFF. If either of them is ON, Press the switch and hold it until the LED goes out.
8) Press switch 8 (EXP A) briefly so that the red LED flashes. Press ENTER/UP, and enter “27” as the Controller Number, then press ENTER/UP to confirm. Next enter a Value of “00” (this is the Low Value), then press ENTER/UP to confirm. Next enter the High Value of “127”, then press ENTER/UP to confirm.
9) Press switch 9 (EXP B) briefly so that the red LED flashes. Press ENTER/UP, and enter “16” as the Controller Number, then press ENTER/UP to confirm. Next enter a Value of “00” (this is the Low Value), then press ENTER/UP to confirm. Next enter the High Value of “127”, then press ENTER/UP to confirm.
10) Press the DOWN switch for 3 seconds.
Programming Footswitch (Preset) 5 as a Tap-Tempo Switch:The Control Change number on the V-Amp to control Tap-Tempo is “64”. Although the actual value sent has no meaning, it requires a Value of “64” or higher to work. So here are the steps to set it up.
1) Select Preset 5 by pressing on footswitch 5.
2) Hold the “Bank Down” switch for 3 seconds.
3) Press the ENTER/UP switch once. The green select LED should be lit. Now that you’re in programming mode, each of the footswitches (1-10) will serve a different purpose depending on what function you’re setting.
4) Make sure all program changes (“PRGCHG1” through “PRGCHG5”) are disabled. The red LEDs should be off for footswitches 1 through 5. If an LED for any one of these switches is ON, that means that Program Change Number is enabled. Press the switch and hold it until the LED goes out.
5) Press switch 6 (CTLCHG 1) briefly so that the red LED flashes. Press ENTER/UP, and enter “64” as the Controller Number, then press ENTER/UP to confirm. Next enter a Value of “64”, then press ENTER/UP to confirm.
6) Make sure the LED for switch 7 (CTLCHG 2) is OFF. If it is ON, Press the switch 7 and hold it until the LED goes out
7) Press switch 8 (EXP A) briefly so that the red LED flashes. Press ENTER/UP, and enter “27” as the Controller Number, then press ENTER/UP to confirm. Next enter a Value of “00” (this is the Low Value), then press ENTER/UP to confirm. Next enter the High Value of “127”, then press ENTER/UP to confirm.
8) Press switch 9 (EXP B) briefly so that the red LED flashes. Press ENTER/UP, and enter “16” as the Controller Number, then press ENTER/UP to confirm. Next enter a Value of “00” (this is the Low Value), then press ENTER/UP to confirm. Next enter the High Value of “127”, then press ENTER/UP to confirm.
9) Press the DOWN switch for 3 seconds.
Now footswitch/preset 5 will function as a Tap-Tempo switch.
Programming Footswitches (Presets) 6 through 10 to select V-Amp Presets 1A through 1E.
Setting up these last 5 presets requires using Program Changes to select the desired patch on the V-Amp. Remember what I stated in the Considerations Section. The V-Amp doesn’t have a Control Change Number to allow you to trigger preset button “A”, you have to use a Program Change to select an actual preset “1A” (Bank 1, Preset A). Program Change 1 = “1A”, 2 = “1B”… all the way up to 125. For example Program Change 14 = “3D”, Program Change 85 = “17E”, etc. Pressing the Bank Up or Down switch will NOT change banks on the V-Amp, it will only change banks on the FCB. If you change banks, all 10 footswitches/presets on the FCB need to be programmed for that bank.
1) Select Preset 6 by pressing on footswitch 6.
2) Hold the “Bank Down” switch for 3 seconds.
3) Press the ENTER/UP switch once. The green select LED should be lit. Now that you’re in programming mode, each of the footswitches (1-10) will serve a different purpose depending on what function you’re setting.
4) Make sure all program changes (“PRGCHG2” through “PRGCHG5”) are disabled. The red LEDs should be off for footswitches 2 through 5. If an LED for any one of these switches is ON, that means that Program Change Number is enabled. Press the switch and hold it until the LED goes out.
5) The LED for PRGCHG1 (switch 1) SHOULD be lit. If it isn’t, press the switch and hold it until the LED turns ON.
6) Press switch 1 (PRGCHG1) briefly so that the red LED flashes. Press ENTER/UP, and enter “01” as the Program Change Number, then press ENTER/UP to confirm.
7) Make sure the LED for switches 6 & 7 (CTLCHG1 and CTLCHG 2) are OFF. If either of them is ON, Press the switch and hold it until the LED goes out.
8) Press switch 8 (EXP A) briefly so that the red LED flashes. Press ENTER/UP, and enter “27” as the Controller Number, then press ENTER/UP to confirm. Next enter a Value of “00” (this is the Low Value), then press ENTER/UP to confirm. Next enter the High Value of “127”, then press ENTER/UP to confirm.
9) Press switch 9 (EXP B) briefly so that the red LED flashes. Press ENTER/UP, and enter “16” as the Controller Number, then press ENTER/UP to confirm. Next enter a Value of “00” (this is the Low Value), then press ENTER/UP to confirm. Next enter the High Value of “127”, then press ENTER/UP to confirm.
10) Press the DOWN switch for 3 seconds.
Raf in NJ
312
Posteur·euse AFfamé·e
Membre depuis 21 ans
Ben perso j'ai programmé mon pedalier comme ca! je tappe deux fois sur mon switch et ca me change de son tout en reglant le tempo. si tu me crois pas tu viens verifier quand tu veux 
Rafouille
toujours pret a s'en metre plein les fouilles
meme si ca cafouille
il a jamais trouille
Rafouille
toujours pret a s'en metre plein les fouilles
meme si ca cafouille
il a jamais trouille
Un seul conseil: Lisez les manuels !!!
greg@37
7
Nouvel·le AFfilié·e
Membre depuis 20 ans
- < Liste des sujets
- Charte
- 1
- 2