Comment Changer La RAM Sur La 3000 ?
- 6 réponses
- 3 participants
- 1 567 vues
- 1 follower
xela-974
19
Nouvel·le AFfilié·e
Membre depuis 18 ans
Franck Débine
1833
AFicionado·a
Membre depuis 21 ans
Salut, y a ca comme info sur le mailing yahoo.
From the Roger Linn Support web page:
Q: How do I expand the MPC3000's memory to 32 megabytes?
A: The maximum sample memory in the MPC3000 is 32 megabytes, or 380 seconds of sample time. To expand an MPC3000 to 32 megabytes:
1. Buy two 16 megabyte, 30 pin (not 72 pin) SIMM memory modules. Any speed will do, parity or non-parity.
2. Open your MPC3000.
3. Look for the small, 3 inch square board in the front right corner of the bottom of the unit. Remove it.
4. In the two SIMM sockets located in the center of the bottom of the unit near the front edge, install the two 16 megabyte SIMMs.
Et ça sur mpc3000.com :
Expanding the MPC3k's memory:
Expanding the MPC3k's memory is fairly easy to do. Just remove the 10 or so screws aroudn the edge of the MPC and setting upright raise the top panel a few inches. Be careful not to pull any of the ribbon cables loose. The memory slots are located right in the front of the MPC. Remove the installed 8 or 2 Meg board that sticks sideways next to the memory slots (if there). Install the two 16 Megs chips in the two white slots. I've found the chip from this company for a very good price (about $50 for the pair). They are the 30 pin SIMM's:
http://www.memoryx.net/mpc3000.html
Si besoin, regarde les deux barettes en bas de la photo, PAS CE QUI EST ENTOURE, juste à gauche. C est ça que tu dois ajouter :
MPCallemand....
From the Roger Linn Support web page:
Q: How do I expand the MPC3000's memory to 32 megabytes?
A: The maximum sample memory in the MPC3000 is 32 megabytes, or 380 seconds of sample time. To expand an MPC3000 to 32 megabytes:
1. Buy two 16 megabyte, 30 pin (not 72 pin) SIMM memory modules. Any speed will do, parity or non-parity.
2. Open your MPC3000.
3. Look for the small, 3 inch square board in the front right corner of the bottom of the unit. Remove it.
4. In the two SIMM sockets located in the center of the bottom of the unit near the front edge, install the two 16 megabyte SIMMs.
Et ça sur mpc3000.com :
Expanding the MPC3k's memory:
Expanding the MPC3k's memory is fairly easy to do. Just remove the 10 or so screws aroudn the edge of the MPC and setting upright raise the top panel a few inches. Be careful not to pull any of the ribbon cables loose. The memory slots are located right in the front of the MPC. Remove the installed 8 or 2 Meg board that sticks sideways next to the memory slots (if there). Install the two 16 Megs chips in the two white slots. I've found the chip from this company for a very good price (about $50 for the pair). They are the 30 pin SIMM's:
http://www.memoryx.net/mpc3000.html
Si besoin, regarde les deux barettes en bas de la photo, PAS CE QUI EST ENTOURE, juste à gauche. C est ça que tu dois ajouter :
MPCallemand....
Anonyme
44
J'ai bien repérer mais la MPC ne prends pas en compte les 2 barrettes de Ram au boot.
Anonyme
44
Franck Débine
1833
AFicionado·a
Membre depuis 21 ans
Anonyme
44
Franck Débine
1833
AFicionado·a
Membre depuis 21 ans
- < Liste des sujets
- Charte